Be sure to see EE World’s APEC 2024 coverage on datacenter power and test equipment.

Alpha & Omega Semiconductor

Electronics generate heat. It’s what they do. Alpha & Omega Semiconductor has developed a package that it calls MEGA IPM7 for its intelligent power modules. The SMD package contains an embedded IGBT for motor drives in appliances such as refrigerators, washing machines, and air conditioners. What makes the package different is its surface contains metal, which helps to pull heat away from the embedded device.

Analog Devices

Analog Devices introduced the LT8418, a 100 V half-bridge GaN gate driver. Designed to minimize EMI issues, the LT8418’s split gate drivers let you adjust a GaN FET’s turn-on and turn-off slew rates. The device can source up to 4 A peak and sink up to 8 A.

Bourns

The manufacturer of power magnetics, circuit-protection devices, sensors, switches, and other devices focused on transformers chokes, gate drivers, and toroids.

Brightworks

Many of the power semiconductors seen at APEC have been designed into phone and laptop chargers from well-known manufacturers such as Anker, Belkin, and others, some of which will remain nameless. Brightworks manufactures chargers and power supplies that other companies private brand, using some of those power semiconductors. The photo shows a 20 W USB-C charger that the company let me take home. I’m tempted to crack open the case to see what’s inside.

Empower Semiconductor

The manufacturer of voltage regulators, silicon capacitors, and interposers exhibited an evaluation board for its EP7123 dual-output integrated voltage regulator. Each output supplies up to 6 A with a 3.3 V input. Other parts in the series include one, three, and four outputs.

Infineon

At APEC 2024, Infineon introduced the TDM22544D and TDM22545D high-density power modules designed for data center processors. The modules package a MOSFET with an inductor that’s surrounded by heat-dissipating metal.

Operating from the Infineon booth, AWL Electricity showed a rather unusual demonstration of wireless power transfer. In this video, Cédric Hamel-Bruneau uses a modified lamp with an LED bulb at one end and no power cord on the other. Instead, the base holds a receiver that receives power from a transmitter. The concept uses electric-fields to transfer power through capacitive coupling. That’s different than, say, a wireless charger that uses magnetic fields and inductive coupling.

Menlo Micro

You might think of Menlo Micro’s switching products for communications, 5G, and test & measurement but the company also makes power switches. The video shows a demonstration of the MM9200 power switch. Here, Menlo Micro shows a set of these switches running in a serial-parallel combination that the company says runs cooler than an identical configuration using SiC.

Microchip

Microchip exhibited the MAICMMC40X120 Aviation Power Core module that integrates an SiC MOSFET with drivers and a microcontroller. It can produce AC power with variable frequencies to drive motors for aerospace and defense applications.

Qorvo

The company introduced a series of SiC 1200 V half-bridge and full bridge power modules. The four modules in the UHBxxx12E1BC3N series have drain currents of 17 A, 25 A, 50 A, and 100 A with R_DS(ON) at 70 mΩ, 35 mΩ, 19 mΩ, and 9.4 mΩ, respectively.

Power Integrations

In the video, Andrew Smith explains how the company achieves multiple DC rails with a single chip. The InnoMux 2-EP is a zero-voltage switching (ZVS) flyback switcher that selects which of its loads needs energy.

TDK

TDK’s µPOL (point-of-load) DC-DC converters provide telemetry for parameters such as voltage, current, and temperature. The demonstration in the video shows a 12 A regulator sending telemetry to a computer. The converter’s output range is 0.6 V to 1.8 V.

The post APEC 2024: Semiconductors, modules, transformers, and chargers appeared first on Power Electronic Tips.

Isn’t electrical power best delivered at high voltage, low current?

Well, yes. For example, the AC power delivered to your neighborhood arrives at thousands of volts. Transformers drop the voltage near the load, which increases the current but over a short distance. That minimizes losses caused by IR drops in the wires. Same for EVs. The batteries can produce hundreds of volts at low current whereupon load voltages are much lower.

The ICs in network equipment are, of course, digital and they can never be fast enough. That’s why logic levels continue to drop. Those 5 V TTL logic levels are too high for today’s high-speed digital devices. The difference between a logic 0 and logic 1 can go below 1 V, often 0.8 V. Why? Because it takes less time to switch between small logic levels.

Such a small difference in logic levels also creates signal-integrity issues. Digital receivers need lots of help distinguishing between logic states and at low voltages and must contend with noise. That brings in signal processing — predistortion and error correction — which also consumes energy.

The following videos highlight demonstrations related to data-center power.

Picotest

In the video below, Steve Sandler explains how Picotest uses a set of ten Analog Devices power modules to convert a 48 V power rail down to 0.8 V at 2000 A. That’s what it takes to power today’s devices. Engineers can use this board to test power rails while the ASIC, emulated by the board, is in development. The board lets engineers control load current from 0 A to 2047 A with 1 A resolution.

STMicroelectronics

Delivering power to a data center encompasses more that just delivering high-current, low voltage power on a board. At APEC 2024 ST’s David Bates demonstrated the company’s offerings.

The ecosystem starts at 48 V, after which regulators bring the voltage down to 12 V. Following that, protection devices keep the main board safe. Each e-fuse can handle up to 60 A or 120 W. The e-fuses are resettable MOSFETs. The final stage drops the voltage to load levels, which can be as low as 0.8 V. That occurs close to the load to minimize IR drops on the board. Bates also explains the concept of phases in DC power delivery.

Texas Instruments

In the Texas Instruments booth, Abhinay Patil demonstrated a power-delivery reference design for servers. The demonstration started with a 12 V power supply. The reference design provides input protection, temperature protection, and short-circuit protection using TPS25990 e-fuses. DC-DC converters drop the voltage to 1.8 V. The board can deliver up to 700 A.

The post APEC 2024: Power to the data center appeared first on Power Electronic Tips.

Featuring a very large aperture of 41.2mm, the DN1000ID current transducer enables power cables with large power connectors to be easily fitted to EV test benches, allowing for quick changeovers. The large aperture is an important advantage as test bench operators often face the issue that the power connectors fitted to the power cables are bigger than the diameter of the cable, making it difficult to fit them in the aperture of the current transducer and often requiring additional work to solve this issue. The new device now offers the best compromise between the 1000A nominal current and aperture size by keeping the best measuring performances in accuracy and phase shift.

The DW500UB-2V high precision fluxgate AC/DC current transducer measures up to 750 A and offers excellent accuracy with 10ppm linearity and low offset at 15 ppm. It meets the increased requirements in terms of high frequency coming from the latest power conversion products based on wide bandgap semiconductor technologies such as gallium nitride (GaN) and silicon carbide (SiC); Danisense has revised its winding processes and now achieves an exceptionally wide bandwidth of up to 10MHz. The main target application is power measurement in laboratories for the design optimization of power converters — typically for e-mobility applications.

Learn more about Danisense here.

The post Danisense to exhibit at APEC 2024 appeared first on Power Electronic Tips.